Fluorescent to LED tube retrofits come in three types. Type A works with the existing ballast, Type B bypasses the ballast and connects directly to line voltage, and Type C uses a remote LED driver. Type B is the most common for long-term retrofits. Panels, strips and wraparounds are often better replaced with a complete LED fixture.
What are Type A, Type B and Type C LED tubes?
| Type |
How it works |
Key points |
| Type A (plug and play) |
Runs on the existing fluorescent ballast |
Fastest install, but the ballast stays and can fail or be incompatible |
| Type B (direct wire) |
Ballast is removed or bypassed, tube is wired to line voltage |
No ballast to maintain, wiring change required |
| Type A+B (hybrid) |
Works on a ballast or wired direct |
Flexible, but confirm the wiring method before installing |
| Type C (remote driver) |
A separate external LED driver powers the tube |
Driver is installed in or near the fixture, wiring change required |
Always read the instructions that come with the exact tube you are installing. Wiring differs by product.
How does a Type A (ballast compatible) tube work?
A Type A tube replaces the fluorescent lamp and keeps the ballast in place. You do not rewire the fixture, so the work is fast. The downside is that the ballast remains a part that can fail, and not every tube works with every ballast. Check the tube maker's ballast compatibility list before you buy in volume.
How does a Type B (direct wire) tube work?
In a Type B retrofit, the ballast is removed or bypassed and line voltage is wired directly to the tube sockets. Once the ballast is gone, nothing in the fixture can fail on the ballast side. Our 120-347V LED T8 tubes suit projects where the voltage varies between buildings.
Type B work needs care:
- Turn off the power at the breaker before you open the fixture.
- Follow the wiring diagram supplied with the tube.
- Do not leave the fixture marked as fluorescent. Relabel it to show it now uses a direct-wire LED tube, as the product instructions describe.
- Check the Canadian Electrical Code and your local authority having jurisdiction (inspector) for any requirements.
What is a hybrid Type A+B tube?
A hybrid tube can run on the existing ballast at first, then be switched to direct wire later when the ballast fails. That makes it useful on mixed-age buildings where you want to start quickly. Confirm the wiring method on the label and the instructions at the time of installation.
What is a Type C tube?
A Type C system uses a remote LED driver, installed with the fixture, to power the tube. It can offer dimming and other control options depending on the driver. The tube and driver need to be matched, so buy them together from the same product line.
When should you replace the whole fixture instead of the tube?
Replace the full fixture when the housing, sockets or wiring are in poor shape, or when you want the cleanest result. Complete LED fixtures are also a good fit when you are updating a space and not just swapping lamps.
A new fixture also removes any worry about old sockets, ballasts or yellowed lenses.
What is the difference between T8 and T5 tubes?
The number is the tube diameter in eighths of an inch, so a T8 is 1 inch across and a T5 is 5/8 inch. T8 is the common size in offices, shops and warehouses, and T5 is slimmer and often found in higher-output and cove fixtures. The two use different sockets, so you cannot swap one for the other in the same fixture. Browse our LED T8 and T5 tubes.
How do I choose the right retrofit type for my project?
- Check the age and condition of the fixtures and ballasts.
- Decide whether you want to touch the wiring. If not, Type A is the quickest, but plan for the ballast to need replacing later.
- If you want the lowest long-term maintenance, choose Type B or a new fixture.
- If you need dimming or controls, look at Type C or a complete LED fixture with the control option you need.
- Test one fixture first, then order for the whole building.
What safety steps should you follow on a retrofit?
- Turn off the power at the breaker and confirm it is off with a tester.
- Follow the fixture label and the tube instructions.
- Remove the old tubes and, for Type B or C, the ballast as directed.
- Attach any new labels required by the instructions.
- Use a licensed electrician where required by your local rules.
Contractor accounts with Net 30 terms are available, subject to approval. See LED lighting supply in Edmonton for more on how we support trade customers.
Frequently asked questions
What is the difference between Type A and Type B LED tubes?
Type A tubes work with the existing fluorescent ballast and need no rewiring. Type B tubes bypass the ballast and connect directly to line voltage, so the ballast is removed or disconnected.
Do I need to remove the ballast for LED tubes?
Only for Type B and Type C systems. A Type A tube keeps the ballast. Follow the instructions supplied with the exact tube you buy.
Do I need to relabel the fixture after a Type B retrofit?
Yes, in most cases. The fixture should no longer be marked as a fluorescent fixture. Follow the tube's instructions and check with your local inspector.
Can I put a T8 LED tube in a T5 fixture?
No. T8 and T5 tubes use different sockets and sizes. Use a tube that matches the fixture, or replace the fixture.
Is it better to retrofit tubes or replace the whole fixture?
Tubes are quicker when the fixture is in good shape. A complete LED fixture is a better choice when the housing, sockets or wiring are worn, or when you want a cleaner result.
Need help matching products or pricing a project? Contact the LitesGo team or call (587) 701-5969. We are at 4914 89 St NW, Edmonton, AB T6E 5K1, and in-stock items usually dispatch in 1-2 business days anywhere in Canada.