Commercial building and parking lot at night lit by LED wall packs and area lights

LED Wall Pack Lights: How to Size and Replace Metal Halide Wall Packs

To replace a metal halide wall pack, match the light output rather than the wattage. A 70W to 150W metal halide wall pack is typically replaced by an LED wall pack of roughly 15W to 40W, and a 250W unit by about 50W to 80W. Mount at 8 to 20 feet and choose 4000K to 5000K for security.

How do I size an LED wall pack?

Size by lumens and mounting height, not watts alone. LED wall packs deliver more usable light per watt than metal halide because metal halide loses light inside the fixture and as the lamp ages. A common approach is to compare the delivered lumens of the old fixture with the new LED.

Old metal halide Typical LED wall pack replacement Typical mounting height
70W to 100W About 12W to 25W 8 to 12 ft
150W About 25W to 40W 10 to 15 ft
250W About 50W to 80W 12 to 20 ft
400W About 80W to 120W 15 to 25 ft

These are rules of thumb. Confirm the lumens, distribution and mounting height for the area you are lighting.

Why replace metal halide wall packs with LED?

LED wall packs typically use far less power for similar light levels, switch on instantly without a warm-up, and avoid the lamp and ballast replacements that metal halide needs. Many also include a photocell or dusk-to-dawn control, which helps reduce operating hours.

  • Lower electrical use for the same job.
  • Instant on and restrike without delay.
  • Less maintenance than lamps and ballasts.
  • Better control options for security lighting.

Replacing the whole fixture is usually simpler than retrofitting a lamp into an old metal halide housing. A new LED wall pack comes with a sealed gasket, a driver and a fresh mounting plate, so it avoids ageing ballasts, cracked lenses and water getting into old housings.

What colour temperature should a wall pack be?

Common choices are 4000K neutral white and 5000K daylight. 5000K looks crisp and is common for security and parking areas. 4000K is a little softer and is often used near buildings and entrances. Some wall packs offer a selectable colour temperature.

What distribution and mounting height do I need?

Wall packs usually come in forward-throw patterns that push light out from the wall, and full-cutoff versions that limit light going upward. Forward-throw suits loading docks, walkways and perimeter areas. Choose a model that reduces glare on neighbouring property, and check your local requirements.

What IP rating and features should I look for?

Outdoor fixtures face rain, snow and dust, so look for a suitable IP rating, such as IP65, for exposed locations. Alberta winters also make cold-weather operation worth checking on the fixture details. Other useful features include photocells, motion sensors and emergency battery backup where needed.

Check the product page for the specifications before you buy. Browse our LED wall pack lights. For large lots and yards, compare LED area, shoebox and flood lights. For other fixtures see our exterior LED lighting fixtures, or explore NEXLEDS.

Should I use a wall pack or a floodlight?

Wall packs are designed to mount flat on a building wall and light the area directly in front of it, such as doors, walkways and loading areas. Floodlights and area lights usually suit open ground, because they are aimed and positioned on poles or brackets.

  • Choose a wall pack for building perimeters, entrances and docks.
  • Choose an area or shoebox light for parking lots and yards.
  • Choose a floodlight for aimable, wide coverage on walls or signs.

Many commercial sites use a mix, with wall packs on the building and pole-mounted lights in the lot.

What should I check before replacing a wall pack?

  • Confirm the supply voltage on the existing circuit.
  • Measure the mounting footprint and the junction box location.
  • Check the old fixture's mounting height and coverage area.
  • Decide whether you want a photocell or motion control.

Disconnect power before removal. Electrical work should be done by a qualified electrician, so check your local code and inspector.

Where can I buy LED wall packs in Edmonton?

LitesGo supplies LED lighting to electrical contractors, builders and property owners from 4914 89 St NW, Edmonton, AB. In-stock items usually dispatch in 1-2 business days and we ship anywhere in Canada. Contractors can apply for Net 30 terms, subject to approval. Shipping terms vary by brand, so see our shipping policy. Read more about LED lighting in Edmonton.

Frequently asked questions

What LED wattage replaces a 150W metal halide wall pack?

A common range is about 25W to 40W of LED, but compare lumens and distribution rather than wattage alone.

What colour temperature is best for a wall pack?

4000K to 5000K is typical. 5000K looks crisp for security and parking areas, while 4000K is a little softer for entrances.

How high should I mount an LED wall pack?

Typical mounting heights run from about 8 to 25 feet depending on the lumen output. Lower wattage units usually suit lower heights.

What IP rating should an outdoor wall pack have?

IP65 is a common choice for exposed outdoor fixtures because it covers dust and water jets. Check the fixture details for the exact rating.

Do LED wall packs need a photocell?

Not required, but a photocell turns the light on at dusk and off at dawn, which helps reduce operating hours for security lighting.

Need help choosing? Contact the LitesGo team or call (587) 701-5969.