A good parking lot lighting plan matches the fixture's light distribution to the layout, mounts it at a suitable pole height, and controls glare and spill light. Area (shoebox) lights are the usual choice for lots, with Type III for edges, Type V for open centres and Type IV for perimeters. A photometric layout confirms the spacing before you order.
What is the difference between area lights and flood lights?
Area lights, often called shoebox lights, are built to throw a controlled pattern across a large flat area from a pole. Flood lights throw a wide, even beam and are often aimed at a building, sign or yard. For lots, driveways and roadways, an area light is usually the better fit because its optics are designed for even coverage and lower glare.
What are Type II, III, IV and V light distributions?
The IES (Illuminating Engineering Society) groups outdoor light patterns into types. In simple terms, the type tells you the shape of the light on the ground.
| Type |
Pattern |
Typical use |
| Type II |
Long and fairly narrow, thrown to the sides |
Narrow lanes, walkways and drive aisles |
| Type III |
Wider, thrown forward and to the sides |
Poles near the edge of a lot, lighting inward |
| Type IV |
Semicircular, strong forward throw |
Poles or walls on the perimeter, lighting away from the edge |
| Type V |
Round, even in all directions |
Poles in the middle of a lot or at an intersection |
Many fixtures offer more than one distribution, and some use a rotatable optic. Check each product page for the available options.
How high should a parking lot light pole be?
Pole height changes how far each fixture reaches and how much glare you get. These are typical ranges only, not code. The right height depends on the site, the fixture, the lumen output and the lighting level you need.
- Small lots and walkways often use shorter poles.
- Mid-sized lots commonly use poles in the range of about 20 to 30 ft.
- Taller poles can cover wider areas, but they cost more and need stronger bases.
Higher mounting gives wider spacing but can create more glare and spill light. Lower mounting needs more poles. A photometric layout is the reliable way to balance them.
How are area lights mounted on a pole?
-
Slip fitter: slides over a tenon at the top of the pole. Common for single fixtures.
-
Arm mount: fastens to the side of the pole, often with two or more fixtures per pole.
-
Trunnion (yoke): lets you adjust the tilt angle. Often used for flood lights.
Match the mount to the pole drilling pattern or tenon size before you order. LitesGo can supply light poles from CECO Poles & Structures in Calgary, quoted for each project. See our light poles page to request a quote.
Do parking lot lights need photocells?
Many sites use a photocell so the lights turn on at dusk and off at dawn without manual switching. Some fixtures include a photocell or have a receptacle for one. Others use a timer, a controller or a motion sensor, which can dim the light when no one is around. Check the product page to confirm what each fixture offers.
How do you limit light trespass and glare?
Light trespass is light that spills onto neighbouring property, roads or windows. To limit it:
- Choose fixtures with a flat lens and a full cutoff design, which keeps light from shining above the horizontal. This is the idea behind dark-sky friendly lighting.
- Keep the fixture level, and use shields where a lot borders homes.
- Pick a lower CCT where neighbours or municipal rules ask for it.
- Check municipal bylaws and development permit conditions for your site.
Why does a photometric layout matter?
A photometric layout shows the expected light levels across the lot before anything is installed. It helps you set pole spacing, choose the distribution type and avoid dark spots or over-lighting. LitesGo provides free DIALux and AGi32 photometric layouts for Technilight fixtures. See our free photometric simulation page for the details.
What should I confirm before ordering parking lot lights?
- The lot dimensions, pole locations and any existing poles or bases that will be reused.
- The distribution type for each pole position.
- The mounting method and the pole drilling pattern or tenon size.
- Whether the fixtures include a photocell or sensor, or need one added.
- The CCT and any municipal or neighbourhood requirements.
- Voltage at the site, and whether the lot has a shared circuit or contactor.
LitesGo also supplied the outdoor lighting retrofit for Save-On-Foods. Contractor accounts with Net 30 terms are available, subject to approval.
Frequently asked questions
What is the best light type for a parking lot?
Pole-mounted LED area (shoebox) lights are the most common choice because their optics spread light evenly across a flat area. The best distribution type depends on where the pole sits in the lot.
What is the difference between Type III and Type V?
Type III is a wider forward and side pattern used near the edge of a lot. Type V is a round, even pattern used in the middle of a lot or at an intersection.
What pole height should I use for a parking lot?
Poles of about 20 to 30 ft are commonly used on mid-sized lots, but this is typical only. The right height depends on the fixture, light level and layout, so use a photometric layout to confirm.
Can LitesGo supply light poles?
Yes. Light poles are available by quote from CECO Poles & Structures in Calgary, quoted for each project.
Does LitesGo provide photometric layouts?
Yes. LitesGo provides free DIALux and AGi32 photometric layouts for Technilight fixtures. Contact us with your site plan to start.
Need help matching products or pricing a project? Contact the LitesGo team or call (587) 701-5969. We are at 4914 89 St NW, Edmonton, AB T6E 5K1, and in-stock items usually dispatch in 1-2 business days anywhere in Canada.