Living room lit by LED pot lights at 3000K warm white

Pot Lights Guide: Sizes, Colour Temperature and How Many You Need

Most homes use 4-inch or 6-inch pot lights spaced about 4 to 5 feet apart, which works out to roughly one light per 16 to 25 square feet of ceiling. Choose 2700K to 3000K for living spaces, 3000K to 4000K for kitchens and bathrooms, and plan about 20 to 30 lumens per square foot in general rooms.

What size of pot light should I choose?

Pot lights, also called recessed lights or potlights, are commonly sold in 3-inch, 4-inch, 5-inch and 6-inch sizes. The size usually refers to the ceiling opening. Smaller sizes give a discreet look, while larger sizes throw more light per fixture.

Size Typical use Typical spacing
3-4 inch Hallways, closets, accent and low ceilings 3 to 5 ft
5-6 inch Kitchens, living rooms, basements, offices 4 to 6 ft
Shallow slim profile Ceilings with limited joist or ductwork space Same as the diameter above

Slim LED discs need very little ceiling depth, which helps in basements and renovations. Browse our LED slim pot lights to compare sizes.

How many pot lights do I need?

Start with the room's lighting target. A common rule of thumb is 20 to 30 lumens per square foot for living rooms and bedrooms, and 40 to 70 lumens per square foot for kitchens, bathrooms and workspaces. Multiply the room area by the target, then divide by the lumens of one fixture.

For example, a 12 ft by 15 ft room is 180 square feet. At 25 lumens per square foot you need about 4,500 lumens, or roughly six fixtures at 750 lumens each. Round up if the room has dark finishes or you want to dim.

What is the right pot light spacing?

A common rule of thumb is to divide the ceiling height in feet by two to get the spacing in feet. An 8 ft ceiling suggests lights about 4 ft apart, and a 9 ft ceiling suggests about 4.5 ft. Place the outer row roughly half that distance from the walls.

  • Wider spacing leaves dark gaps and scalloped walls.
  • Tighter spacing increases glare and cost.
  • Use a wider beam angle for even coverage and a narrower one for accent lighting.

What colour temperature works best for pot lights?

Colour temperature is measured in kelvins (K). Lower numbers look warmer and higher numbers look cooler and bluer. Typical choices are listed below.

Colour temperature Look Common rooms
2700K Warm white Bedrooms, living rooms, dining rooms
3000K Soft white Kitchens, hallways, bathrooms
4000K Neutral white Garages, laundry rooms, offices
5000K Daylight Workshops, utility and task areas

Try to keep one colour temperature within a connected space so the light looks consistent from room to room. Some fixtures offer a selectable colour temperature switch, which makes it easier to decide on site.

What should I check before buying LED pot lights?

Look at the fixture details before you order. A short checklist helps avoid returns.

  • Insulation contact: Ceilings with insulation typically need an IC-rated fixture.
  • Damp or wet rating: Showers and covered outdoor soffits need a suitable rating.
  • Dimming: Match the fixture to a compatible LED dimmer to avoid flicker.
  • Ceiling depth: Confirm the space above the drywall.
  • Local rules: Check your local code and inspector for requirements in your area.

Pot lights suit most rooms, but not every ceiling. For surface-mounted options where recessing is not practical, see our flush mount ceiling lights. For bathrooms, also consider a vanity light at the mirror for face lighting.

What are common pot light layout mistakes?

The most common mistake is installing too many lights in a single grid. A better plan layers light by purpose and keeps each circuit on a dimmer.

  • Placing lights directly above seating, which can cause glare on screens.
  • Ignoring cabinets, so the light falls on cabinet doors instead of the counter.
  • Mixing colour temperatures between rooms that share an open layout.
  • Skipping a dimmer, which limits how a room can be used in the evening.

For kitchens, position lights about 24 to 30 inches from the wall so they fall on the counter.

Where can I buy LED pot lights in Edmonton?

LitesGo supplies LED lighting to homeowners, electrical contractors and builders from 4914 89 St NW, Edmonton, AB. In-stock items usually dispatch in 1-2 business days and we ship anywhere in Canada. Contractors can apply for a Net 30 account, subject to approval. Shipping terms vary by brand, so review our shipping policy. Learn more about our LED lighting in Edmonton.

Frequently asked questions

Are pot lights and recessed lights the same thing?

Yes. Pot lights, potlights and recessed lights all describe fixtures installed into a ceiling opening so the trim sits close to flush with the surface.

How far apart should pot lights be?

A common rule of thumb is to divide the ceiling height in feet by two. An 8 ft ceiling typically suggests about 4 ft between lights, adjusted for the beam angle and the room layout.

What colour temperature is best for a kitchen?

Many kitchens use 3000K to 4000K. 3000K feels softer and 4000K looks crisper for food prep. Keep the same colour temperature across the kitchen and nearby rooms.

Can I put pot lights in an insulated ceiling?

Typically you need an IC-rated fixture where insulation may touch it. Always check the fixture markings and ask your local code authority or inspector.

How many lumens do I need per pot light?

It depends on the room. Divide the total lumens needed for the room by the number of fixtures. Many general-purpose pot lights fall in the 600 to 1,000 lumen range.

Need help choosing? Contact the LitesGo team or call (587) 701-5969.