Explosion Proof Lighting Guide: Class I Division 1 vs Division 2, Groups and T-Codes

Industrial plant with explosion-proof light fixtures on pipe racks

Hazardous location lighting is built for areas where flammable gas, vapour, dust or fibres may be present. In Canada, fixtures are chosen by Class (the type of hazard), Division (how likely it is), Group (the specific material) and T-code (the maximum surface temperature). Confirm the classification before you buy: it is set by the facility, not by the fixture supplier.

What is hazardous location (HazLoc) lighting?

A hazardous location is an area where a fire or explosion could start if a spark or hot surface meets a flammable material in the air. Typical examples include fuel handling, paint and coating areas, grain and wood dust operations, battery and chemical rooms, and some oil and gas facilities.

HazLoc fixtures are built so that an ignition inside the fixture cannot escape, or so that the fixture cannot create a spark or surface hot enough to ignite the surrounding atmosphere. Ordinary LED fixtures are not designed for these areas, even if they are sealed or wet rated.

What are Class I, Class II and Class III locations?

Class Hazard Examples
Class I Flammable gases or vapours Fuel storage, spray booths, pump rooms
Class II Combustible dust Grain handling, flour, some metal dust processes
Class III Ignitable fibres or flyings Textile and wood processing

Most explosion proof lighting enquiries are for Class I, because it covers gases and vapours. Our hazardous location and explosion-proof lighting collection and hazardous location LED lighting collection are the places to start. Check each product page for the exact Class, Division and Group marking.

What is the difference between Division 1 and Division 2?

Division 1 means the hazard is expected to be present during normal operation, or may exist often because of repairs, maintenance or leakage. Division 2 means the hazard is normally contained and would only be present under abnormal conditions, such as a leak or equipment failure.

Division 1 fixtures are built to a stricter standard than Division 2 fixtures. A Division 1 fixture can usually be used in a Division 2 area, but a Division 2 fixture is not acceptable in a Division 1 area. Browse the two ranges here:

What are gas groups A, B, C and D?

For Class I, materials are sorted into Groups A to D by how easily they ignite and how violent the explosion can be. A fixture is marked for the groups it is approved for.

  • Group A: acetylene.
  • Group B: hydrogen and similar gases.
  • Group C: ethylene and similar materials.
  • Group D: common materials such as propane, gasoline and natural gas.

Many industrial lighting fixtures are approved for Groups C and D or for Group D only, since those cover a large share of oil, gas and fuel applications. Dust areas use Groups E, F and G under Class II. Always match the fixture marking to the group stated in the area classification.

What do temperature codes (T-codes) mean?

The T-code is the maximum surface temperature the fixture can reach in operation, shown as T1 through T6. A lower number means a higher allowed temperature, and a higher number such as T6 means a cooler surface.

The fixture must have a T-code that is cooler than the ignition temperature of the material in the area. A fixture marked T4 or T5, for example, runs cooler than one marked T3. Check the fixture marking against the facility's requirement, not only the Class and Group.

If your area is hot for other reasons, such as a drying or baking room, a different fixture type may apply. See high temperature LED high bay lights for high ambient temperature applications, and confirm that the fixture is also approved for the hazardous classification you need.

Does Canada also use the Zone system?

Yes. The Canadian Electrical Code recognizes both the Class and Division system and the Zone system, which is used internationally. Zones 0, 1 and 2 are used for gases, with Zone 0 being the most hazardous. Equipment is marked to match the system used at the facility.

Many existing Canadian facilities, and a large share of the fixtures sold here, are still classified by Class and Division. Do not try to convert one system to the other yourself.

How do you choose between high bay, linear and flood fixtures?

  • High bay: best for high ceilings in warehouses, fuel facilities and plants.
  • Linear: suits lower ceilings, corridors, spray booths and pump rooms where a long, even pattern helps. See explosion proof LED linear lights.
  • Flood and wall mount: used for exterior areas, tanks and loading zones. Check the product pages for hazardous-location models.

For voltage, many commercial and industrial fixtures offer 120-347V drivers, and some products are made for 200-480V supplies. Check the voltage range on the label against your circuit, and read our guide to 347V lighting in Canada for more on this.

Who confirms the classification?

The facility owner and a qualified person set the area classification, normally shown on area classification drawings. Confirm the Class, Division, Group and T-code with those drawings and with the authority having jurisdiction (AHJ) before you order. Check the Canadian Electrical Code and your local inspector for wiring methods, seals and installation rules.

For projects in Alberta, see our commercial lighting supply in Edmonton. Contractor accounts with Net 30 terms are available, subject to approval.

Frequently asked questions

What does Class I Division 1 mean?

Class I means flammable gas or vapour. Division 1 means the hazard is present in normal operation or often because of maintenance or leaks. It needs the strictest fixture protection.

Can a Division 1 fixture be used in a Division 2 area?

Usually yes, if the Class, Group and T-code also match. A Division 2 fixture should not be used in a Division 1 area. Confirm with the area classification and the AHJ.

What do Groups A, B, C and D mean?

They sort Class I materials by ignition characteristics. Group A is acetylene, B is hydrogen, C is ethylene and D includes propane, gasoline and natural gas. A fixture must be approved for the group in your area.

What is a T-code on an explosion proof light?

It is the maximum surface temperature of the fixture, from T1 to T6. The surface temperature must stay below the ignition temperature of the material in the area.

Who decides which hazardous location rating I need?

The facility's area classification drawings set it, and the authority having jurisdiction confirms it. A supplier cannot decide the classification for you.

Need help matching fixtures to your classification? Contact the LitesGo team or call (587) 701-5969. We are at 4914 89 St NW, Edmonton, AB T6E 5K1, and in-stock items usually dispatch in 1-2 business days anywhere in Canada.