IP Ratings for Light Fixtures Explained: IP44, IP65, IP66, IP67 and IP69K

An IP rating has two digits. The first shows protection against solid objects and dust, and the second shows protection against water. IP44 resists splashing, IP65 is dust-tight and resists water jets, IP66 resists powerful jets, IP67 handles temporary immersion, and IP69K is made for high-pressure, high-temperature washdown. Higher is not always better, so match the rating to the space.

What do the two digits in an IP rating mean?

IP stands for Ingress Protection. The first digit runs from 0 to 6 and describes protection against solids such as fingers, tools and dust. A 6 means the fixture is dust-tight. The second digit runs from 0 to 9 and describes protection against water, from drips up to powerful jets and immersion.

If a digit is replaced with an X, for example IPX4, that aspect was not rated. The letter K in IP69K is a separate road-vehicle test designation for high-pressure, high-temperature cleaning.

What do IP44, IP65, IP66, IP67 and IP69K mean?

Rating What it protects against Typical use
IP44 Small solids, splashing water from any direction Bathrooms, covered entries, damp rooms
IP65 Dust-tight, low-pressure water jets Parkades, loading docks, general outdoor and industrial
IP66 Dust-tight, powerful water jets and heavy seas Car washes, wash bays, exposed outdoor areas
IP67 Dust-tight, temporary immersion in water Areas that can flood or be submerged briefly
IP69K Dust-tight, high-pressure and high-temperature water jets Food plant washdown and heavy sanitation

An IP67 fixture is not automatically IP66, because the tests are different. Where you need both, look for a fixture that lists both ratings.

What is the difference between damp and wet locations?

Damp and wet are location categories used in electrical codes and in product listings. A damp location is protected from direct water but exposed to moisture or condensation, such as a covered porch or a bathroom away from the shower. A wet location is exposed to direct water contact, such as rain, a shower spray or washdown.

IP ratings and damp or wet listings are separate systems. Ask for both where it matters: the listing tells you where the fixture is approved to be installed, and the IP rating tells you how well it is sealed. Check the Canadian Electrical Code and your local authority having jurisdiction (inspector) for requirements in each space.

Which IP rating do you need for each space?

  • Bathrooms and showers: use a fixture listed for wet or damp location, depending on how close it is to the water. See wet rated pot lights for recessed options.
  • Parkades: moisture, dust, road salt spray and cleaning are common, so IP65 or higher vapor tight fixtures are a typical choice.
  • Car washes and wash bays: direct jets are expected, so look at IP66 or higher, and check the product for corrosion resistance.
  • Food plants: areas that are hosed down with hot water and cleaning chemicals often call for IP69K or the rating specified by the plant's sanitation program.
  • Outdoor areas: choose a wet location listing and an IP65 or IP66 rating at minimum. Browse commercial outdoor lighting.
  • Auto repair shops: shops have dust, moisture and cleaning, so sealed fixtures are common. See automotive shop lights.

What is a vapor tight light, and how does it relate to IP ratings?

A vapor tight fixture has a sealed housing and a gasketed lens that keep moisture, dust and vapour out of the lamp compartment. Many vapor tight lights are rated IP65 or higher, but check the label on each product.

They are used in parkades, car washes, cold storage, food processing, and other harsh or damp interiors. Browse the LED vapor tight lights collection or the broader wet location and vapor tight lighting range, and read each product page for the exact rating.

Does a higher IP rating always mean a better fixture?

No. The right rating depends on the space. An IP69K fixture in a dry office adds cost without benefit, while an IP44 fixture in a car wash will not last. Corrosion resistance, material and gasket quality also matter in harsh areas, and these are not shown by the IP number alone.

Also remember that an IP rating applies to the fixture as sold. If the installer drills extra holes, uses the wrong cable gland or leaves a gasket out, the rating no longer holds.

For project help in Alberta, see our commercial lighting supply in Edmonton. Contractor accounts with Net 30 terms are available, subject to approval.

Frequently asked questions

What does IP65 mean on a light fixture?

IP65 means the fixture is dust-tight and protected against low-pressure water jets from any direction. It is a common rating for parkades, loading docks and outdoor lighting.

What is the difference between IP65 and IP66?

Both are dust-tight. IP66 is tested against more powerful water jets than IP65, so it suits car washes and exposed outdoor areas better.

What does IP69K mean?

IP69K means the fixture is dust-tight and withstands close-range, high-pressure, high-temperature water jets. It is used for washdown areas such as food processing.

Is IP67 the same as waterproof?

IP67 means the fixture can survive temporary immersion in water under test conditions. It does not mean it can be left underwater permanently, and it is not the same as IP66 jet protection.

Do I need a wet location listing as well as an IP rating?

Often yes. The wet or damp location listing tells you where a fixture may be installed, and the IP rating shows how well it is sealed. Check the code and your local inspector for each space.

Need help choosing the right rating for your project? Contact the LitesGo team or call (587) 701-5969. We are at 4914 89 St NW, Edmonton, AB T6E 5K1, and in-stock items usually dispatch in 1-2 business days anywhere in Canada.