Canopy and Gas Station LED Lighting Guide

The best LED canopy light for a gas station is a low-glare fixture with a wet or damp rating suited to the canopy, mounted flush to the underside or recessed into it. Choose a wattage and colour temperature that give even light across the pumps, and check whether you are replacing metal halide so you can match the mounting.

What is a canopy light?

A canopy light is a downward-facing fixture made for the underside of a covered area, such as a gas station canopy, a drive-through, a building entrance or a parkade. It is designed to put even light on the ground and work surfaces while keeping glare low for drivers and customers.

Surface-mounted or recessed canopy lights?

Mounting How it works Good fit
Surface-mounted Fixture mounts on the underside of the canopy Retrofits, parkade ceilings, canopies with no cavity
Recessed Fixture sits in a cut-out so its face is nearly flush New builds and canopies with a cavity, where a clean flush look matters

Confirm the mounting type on each product page before you order, and measure the canopy cavity if you plan to recess fixtures. Browse the full LED canopy and garage lights range to compare options.

How do you control glare under a canopy?

Glare matters at night, when drivers pull in under a bright canopy. Several things help:

  • Use fixtures with a diffused or recessed lens so the light source is not visible from a distance.
  • Choose a wattage that suits the canopy height instead of the brightest option.
  • Space fixtures evenly so there are no harsh bright spots.
  • Pick a colour temperature that suits the site, using our colour temperature guide.

Several of our canopy lights offer selectable wattage and colour temperature, shown in the product title as ranges such as 40-60W or 3CCT.

What wet or damp rating does a canopy light need?

A canopy keeps off direct rain and snow, but wind, splashing and washdown can still reach the fixtures. Many canopies and parkades use fixtures rated for damp or wet locations, and a wet rating is the safer choice for exposed edges and cold, wet winters. For example, the Votatec 60W LED Canopy Light, 40-60W, 8,700 lm, 3CCT, IP65, 120-347V lists an IP65 rating in its title. See our IP ratings guide for what the numbers mean, and check each product page for its rating.

Which canopy light wattage should you choose?

We group canopy lights by wattage range, so you can start from the size you need:

  • LED canopy lights up to 60W, for lower canopies, entrances and smaller covered areas. Examples include the Technilight LED Canopy Light 23-45W and the Votatec 60W LED Canopy Light with PIR Sensor, 18-60W.
  • LED canopy lights 70-120W, for taller canopies and larger covered areas. Examples include the NEXLEDS LED Canopy Light, 40-80W, 3CCT, 120-347V, and the Technilight LED Canopy Light 80-120W.

Several models are listed with a 120-347V input range, which suits both 120V and 347V commercial supplies. See our 347V lighting guide for details. Some models include a PIR sensor, as shown in the product title.

Can you use canopy lights in a parkade?

Yes. Many parkades use canopy-style fixtures on the ceiling, because they are built for covered, often damp spaces. Choose fixtures with a suitable wet or damp rating, and consider PIR-sensor models for stairwells and low-traffic areas. Browse parking garage and canopy lighting for the full selection.

How do you retrofit metal halide canopy fixtures with LED?

  1. Count the existing fixtures and note the mounting type: surface, recessed or pendant.
  2. Record the existing wattage and mounting height, then pick an LED wattage that gives the light level you want.
  3. Choose a fixture that fits the existing opening or bracket. This keeps the retrofit simple.
  4. Disconnect and remove the old ballast and fixture. A qualified electrician should handle the wiring.
  5. Confirm the supply voltage, since our canopy lights with a 120-347V range suit common commercial supplies.

For outdoor and exterior retrofits, LitesGo supplied the outdoor lighting retrofit for Save-On-Foods. Send us your fixture list and we will help you match LED replacements.

Frequently asked questions

What is the best light for a gas station canopy?

A low-glare LED canopy light with a wet or damp rating suited to the canopy, at a wattage that gives even light across the pumps. Check the mounting type and the supply voltage first.

Can I replace metal halide canopy lights with LED?

Yes. Choose an LED fixture that fits the existing mounting, remove the old ballast, and have a qualified electrician do the wiring.

Are canopy lights wet-rated?

It depends on the model. Check the product page for the rating. Some models list an IP65 rating in the product title.

Do canopy lights work on 347V?

Many of our canopy lights are listed with a 120-347V input range, which covers both common commercial supplies. Confirm on the product page.

Can I use canopy lights in a parking garage?

Yes. Canopy-style fixtures suit covered parkades. Choose a wet or damp rating that matches the space, and consider a PIR sensor in low-traffic areas.

Need help choosing canopy lighting for a station, drive-through or parkade? Contact the LitesGo team or call (587) 701-5969. We are at 4914 89 St NW, Edmonton, AB T6E 5K1, and in-stock items usually dispatch in 1-2 business days anywhere in Canada.