LED Tape Light Voltage Drop, 5 m Reels and How to Size the Driver

Reel of warm white LED tape light next to a power supply on a workbench

Low-voltage LED tape is usually sold in 5 m reels because about 5 m is the longest run that most tape can be fed from one end before voltage drop makes the far end visibly dimmer, or shifts its colour. Longer runs need extra feed points, not reels joined end to end. Use this guide to plan the feeds, then size the driver with our LED tape light calculator.

This is the deep dive. For the basics of 12V vs 24V, COB vs SMD and channels, start with our LED strip lights guide.

What is voltage drop in LED tape light?

Current flows through thin copper traces printed on the tape. Those traces have resistance, and resistance multiplied by current is lost voltage. The further the current travels, the more voltage is lost.

The result is that the far end of the tape receives less voltage than the end near the driver. It looks dimmer. On RGB and tunable-white tape the colour can also shift, because the different colour channels are affected differently.

The effect grows with two things: run length and current. Higher-wattage tape draws more current, so it reaches its limit on a shorter run.

Why does 24V tape handle longer runs than 12V?

For the same wattage, a 24V tape draws half the current of a 12V tape (current equals watts divided by volts). Less current through the same copper means less voltage lost. That is why most architectural and commercial tape is 24V, and why most of the tape we stock is 24V.

For long runs, choose 24V. Even then, keep each fed segment within the manufacturer's maximum run length.

Why do some tapes come in 25 m reels?

We carry NEXLEDS 120V 12 mm COB Tape Light, 6W/m, IP67, 25 m and NEXLEDS 120V RGB SMD Tape Light, 7W/m, IP65, 25 m. At line voltage the current for the same wattage is much lower, so long runs are possible.

This tape connects to line voltage through its own power cord or connector (see the tape light connectors and drivers collection for starter cables). Install it per the manufacturer's instructions and the Canadian Electrical Code, and check with your local authority having jurisdiction (inspector).

Why does neon flex come in 5 m or 10 m reels?

Neon flex is also low-voltage and is limited by the same effect, so it is supplied in set lengths. Our flexible lighting range includes NEXLEDS neon flex in 5 m and 10 m lengths. Check the maximum run on each product's spec sheet before you plan a layout, and do not extend past it.

How do you wire long runs of LED tape?

These methods are common practice, and they all aim to keep each fed section short:

  • Parallel feeds (home runs). Run a separate pair of wires from the driver to the start of each 5 m segment. This is the most reliable approach for long runs.
  • Feed both ends. Powering a run from both ends shortens the distance the current has to travel, which evens out brightness. Stay within the manufacturer's guidance for the run.
  • Use suitable wire for the leads. On long leads between the driver and the tape, the wire gauge matters. Thin wire drops voltage too. Use a heavier gauge as the lead gets longer, and check the tape's spec sheet. Our connectors collection includes Dainolite Sleeved Pair 18GA WIRE AWM 105C/-per Foot (CMG18-16T) and splitters.
  • Keep the driver close to the tape. Keep the low-voltage leads as short as the installation allows, and put the long distance on the mains side of the driver instead.
  • Never daisy-chain reels. Do not join several reels end to end on one feed beyond the manufacturer's maximum run.

Run length to feed method

Run length (24V tape) Feed method
Up to 5 m One feed at the start of the reel
5 m to 10 m Two parallel feeds, one per 5 m segment, or feed both ends if the manufacturer allows it
10 m to 15 m Three parallel feeds from the driver, one per 5 m segment
More than 15 m One feed per 5 m segment, often on more than one driver or output

Think of it as a star layout: the driver is the centre, each 5 m segment hangs off its own pair of wires like a spoke, and no segment is powered through another one. These are rules of thumb. The tape's spec sheet always wins.

How do you calculate the driver size for LED tape?

Follow these steps, or enter your run in the LED tape light calculator:

  1. Find the tape's watts per metre (W/m) on the product page.
  2. Total watts = W/m x metres.
  3. Minimum driver = total watts / 0.8. Loading a driver to no more than about 80% is common practice and leaves headroom.
  4. Choose the next standard driver size up.

To work in feet, 1 m = 3.28 ft, so divide W/m by 3.28 to get W/ft. For example, 8W/m is about 2.44 W/ft. A 20 ft run of that tape is about 49W, which needs about 61W, so choose a 75W driver.

Worked examples with LitesGo products

Example Total watts Divide by 0.8 Driver choice
NEXLEDS 8mm COB tape, 8W/m, one 5 m reel 8 x 5 = 40W 50W 60W driver
Dainolite 17.3W/m tape, one 5 m reel 17.3 x 5 = 86.5W about 108W 120W or more, or split into two circuits
12 m kitchen run of 6W/m tape 6 x 12 = 72W 90W 96W or larger

For the kitchen run, split the 12 m into three feeds of about 4 m each, about 24W per feed, all wired back to the driver. Each segment gets full voltage, and the run is well within the reach of a single driver.

Which drivers does LitesGo stock?

  • NEXLEDS 24V Class 2 LED Driver, Triac Dimmable, 120-277V
  • NEXLEDS 24V Class 2 LED Driver, 5 Dimming Options, 120-277V
  • NEXLEDS Dimmable LED Tape Light Driver, 24W to 288W
  • Dainolite 24V drivers in 16W, 20W, 30W, 60W, 75W and 96W, plus a 96W plug-in driver

Browse them in the tape light connectors and drivers collection. For general driver selection, read how to choose an LED driver.

Why do Class 2 drivers limit how much tape you can run?

Class 2 power supplies are limited in output power (commonly 100W per output). That limit is a common reason long runs are split across multiple drivers or outputs. Check the driver's label for its rating and output limits, and follow the Canadian Electrical Code and your local inspector for installation rules.

How do you match the driver and the dimmer?

The driver and the dimmer must match. A triac-dimmable driver needs a triac-compatible dimmer, an ELV driver needs an ELV dimmer, and a 0-10V driver needs a 0-10V control. Using the wrong type can cause flicker, buzzing or poor low-end dimming. Check both datasheets.

Which LitesGo tape lights have which reel length?

Widths, wattages and reel lengths below come from the product titles. Check each product page for the exact model and specs.

Product Width W/m Reel Voltage / IP
NEXLEDS 3mm COB tape 3 mm 4 5 m 24V, IP20
NEXLEDS 5mm COB tape 5 mm 6 5 m 24V, IP20
NEXLEDS 8mm COB tape 8 mm 8 5 m 24V, IP20 or IP65
NEXLEDS 12mm COB tape 12 mm 11 5 m 24V, IP20
Dainolite IP33 tape 8 mm 4.8 5 m 24VDC, IP33
Dainolite IP33 tape 10 mm 14.4 or 17.3 5 m 24VDC, IP33
NEXLEDS 120V 12 mm COB tape 12 mm 6 25 m 120V, IP67
NEXLEDS 120V RGB SMD tape - 7 25 m 120V, IP65
NEXLEDS 10 mm neon flex 10 mm 10 5 m IP67
NEXLEDS 16 mm neon flex 16 mm 5.5 5 m IP67
NEXLEDS 20 mm neon flex 20 mm 13 10 m IP67

Shop the full range in LED tape lights and NEXLEDS strip lights. Add aluminum LED tape light channels for a cleaner finish, and read our under cabinet lighting guide if the run is going under cabinets.

Contractor accounts with Net 30 terms are available, subject to approval.

Frequently asked questions

Why are LED strips sold in 5 m rolls?

Most low-voltage tape is made in 5 m reels because about 5 m is the longest run that can usually be fed from one end before voltage drop makes the far end dimmer. Longer runs need extra power feeds, not reels joined end to end.

Can I connect two 5 m strips together?

Only if the manufacturer's maximum run length allows it. Joining reels end to end on one feed adds length and current to the same thin copper traces. Feed each 5 m segment from the driver with its own wires instead.

How do I calculate the LED driver size?

Multiply the tape's watts per metre by the length in metres to get total watts, divide by 0.8 so the driver is loaded to no more than about 80%, then choose the next standard driver size up.

Why is the end of my LED strip dimmer?

Voltage drop. Current flowing through the thin copper traces loses voltage along the run, so the far end receives less and looks dimmer. Feed the tape from both ends or add a parallel feed to each 5 m segment.

12V or 24V for long runs?

24V. For the same wattage a 24V tape draws half the current of a 12V tape, so it loses less voltage along the run. Even so, keep each fed segment to the manufacturer's maximum run length.

Need help planning feeds or pricing a project? Contact the LitesGo team or call (587) 701-5969. We are at 4914 89 St NW, Edmonton, AB T6E 5K1, and in-stock items usually dispatch in 1-2 business days anywhere in Canada.