To retrofit a fluorescent sign to LED, replace the fluorescent tubes with LED sign tubes or modules, and remove or bypass the old ballasts if the new product calls for it. Match the tube length and the cabinet depth, wire each side of a double-sided cabinet, and plan access for future maintenance.
Why retrofit a fluorescent sign to LED?
Fluorescent sign tubes need ballasts, and both can fail over time, especially in cold weather. LED sign tubes and modules replace that setup with a simpler, longer-lasting light source in the same cabinet. Retrofitting keeps your existing sign cabinet and faces, so you avoid a full sign replacement.
LitesGo supplied the LED signage retrofit and outdoor lighting retrofit for Save-On-Foods.
What is the difference between LED sign tubes and LED modules?
| Option |
What it is |
Good for |
| LED sign tubes |
Tube-shaped LED lamps that replace fluorescent sign tubes |
Pylon and cabinet signs that already hold tube sockets or brackets |
| LED modules |
Small LED units on a strip or rail, spread across the cabinet |
Shallow cabinets, channel letters, even backlighting |
Browse LED sign tubes and the full LED sign and pylon retrofit lighting range to compare options. If your sign uses standard T8 fluorescent tubes, see our T8 LED tubes as well.
How do you retrofit a double-sided sign cabinet?
A double-sided cabinet has a lit face on each side, usually with tubes or modules running inside between them. The goal is even light on both faces.
- Open the cabinet and note the tube length, the spacing between tubes and the cabinet depth.
- Choose LED tubes or modules that give even light to both faces. Some cabinets use one row of tubes for both sides, others use two.
- Mount and wire the new tubes, and keep the spacing close to the original layout.
- Test both faces after dark to check for hot spots or dim areas.
What is a ballast bypass and do you need one?
A fluorescent ballast regulates power to the tube. Some LED tubes run on the existing ballast, but many are wired directly to line voltage, which means the ballast is removed or bypassed. Direct-wire LED tubes remove the ballast as a future failure point.
Check the product page to see how each tube is wired, and do not mix methods inside one cabinet. Have a qualified electrician do the wiring, and confirm requirements with your local authority having jurisdiction. Our fluorescent to LED retrofit guide explains the differences between tube types.
Do LED sign tubes start in cold weather?
Cold weather is a common reason fluorescent signs flicker or start slowly. LEDs generally do not have that problem, which is one reason many owners in colder climates retrofit. Check each product page for its operating temperature range before you order for outdoor use.
What about voltage on pylon and cabinet signs?
Commercial signs are often fed at 120V or 347V. Confirm the sign's supply voltage before choosing tubes, then pick products with a matching input range. Our 120-347V T8 tubes and 347V guide cover the details.
How do you plan for maintenance access?
- Choose tubes or modules that can be replaced one at a time, without taking the whole cabinet apart.
- Keep wiring tidy and labelled so a future technician can trace each run.
- Leave room for a lift or ladder at pylon signs, and note the access method for your maintenance team.
- Record the product model and quantity used, so you can reorder matching parts.
Frequently asked questions
Can I replace fluorescent sign tubes with LED?
Yes. LED sign tubes and modules are made for this. Match the tube length and cabinet layout, and check whether the ballast must be removed or bypassed.
Do I need to remove the ballast?
It depends on the product. Some LED tubes work with the existing ballast, while many are direct-wire and need the ballast removed or bypassed. Check the product page.
Can I retrofit a double-sided sign?
Yes. Wire the tubes or modules so both faces light evenly, and test both sides after dark.
Will LED sign lighting work in a cold Canadian winter?
LEDs generally start without the delays common to fluorescent tubes in cold weather. Check the operating temperature range on the product page for outdoor signs.
Can LitesGo help size a sign retrofit?
Yes. Send us the sign type, tube length, cabinet depth and supply voltage, and we will help you match tubes or modules.
Need help with a sign retrofit? Contact the LitesGo team or call (587) 701-5969. We are at 4914 89 St NW, Edmonton, AB T6E 5K1, and in-stock items usually dispatch in 1-2 business days anywhere in Canada.